I’ve always had the desire to attempt the process of reupholstering a chair.Â Quite a few of my blogger friends did and the results were amazing, but I was still reluctant – Could I really do it?Â
After reading this post, for some reason, “it” clicked and I was on-board.Â My mission of finding a chair had started.Â I needed something new anyway for my desk since I’ve been using this chair which has no seat padding and gets uncomfortable after a while. It took some time, but one day when on a thrifting adventure with my mom, I spotted it and bells started to ring.
Let me start off by saying, I have no upholstery skills, so this is something that absolutely ANYONE can do.Â If I can do it, so can you!Â Don’t get me wrong, there were quite a few times that I wanted to give up, but I kept chug, chug, chugging along and I’m thrilled with the results of a comfortable, stylish, and inexpensive desk chair.
It all started off here…
I began by removing the fabric from the back of the chair.Â The old fabric was secured with ALOT of staples (which brought back memories of the carpet on the stairs), so using plyers I (and the mister) removed each and every one.Â It took a while and part of the surrounding wood on the chair got slightly damaged, but it ended up being fine since the new fabric and trim covered it later.
The seat upholstery I left since it was in fine condition and the new fabric would cover right over.
Once the fabric was stripped down, it was time to give this chair a paint makeover.Â Up until this point, I had never before tried the Annie Sloan Chalk Paint and thought this would be the perfect piece.Â Because of the ASCP formula, there is no need to sand before painting and I was ALL FOR THAT! Holla…
I had some hurdles to overcome with the paint and wax, but all in all, I was happy with the result.Â My experience with the paint is a story in itself, which you’ll have to wait for later this week. (Click HERE to read about My First Annie Sloan Experience)
Anyway, here is me painting the chair…
Two coats later, I then added the clear wax as top coat.
Once that was done and dry (remember, I’ll chat more about my ASCP experience later this week), the reupholstery work began.Â I was psyched to start this part of the project.Â I chose a brown and white chevron pattern for the back panel, along with a burnt orange and white patterned fabric for the seat and back. The chevron fabric I had leftover from a pillow and table runner, while the orange fabric is a panel that I purchased from Target to use for this project and some new pillows (that I have yet to make – story of my life).
I started with the chevron fabric first and stapled it to the inside of the wood trim surround in place of where the previous fabric was. (this is a few from the front of the chair)
Once the fabric was stapled all around, this is how it looked from the back…
Then it was time to work on the seat and back reupholstery.Â I started with the back.Â I added back the original foam insert that was previously used, stapled all the way around, and finished by trimming the leftover fabric with scissors.
Then I used the same steps for the seat.
Once I exhausted out my staple gun, this was the result…
Eek! Those edges don’t look good.Â BUT WAIT… here’s how I fixed it.
Trim is the key to
novice upholstery perfection!Â Using a good ole’ hot glue gun, I added the trim surround to cover all the ragged edges of where I used the scissor to trim the fabric.
And minutes later, this was the result.
I am thrilled with the final upholstery project and glad that through some tough parts (mostly the removal of the old staples and fabric), I stuck with it.Â This chair really gives such a fun flair to my office area. The chair is temporarily in this spot while my front room / office space is under remodel.
And here’s me working away (thanks to my 6 yr. old for snapping this shot) …
Have you ever reupholstered a piece of furniture?Â Did you find the first time easier or more difficult than you thought? What DIY projects have you been working on lately?